F6 Maintenance and Repair — Management Level
507 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 1.Which of the reasons is the least likely for the high temperature of the oil in the turbocharger unit?
- 2.Reversing a main marine diesel engine is required when:
- 3.What should we change when reversing a main marine diesel engine?
- 4.Are four-stroke marine diesel engines reversible?
- 5.What is the purpose of blocking devices in the reversing system of main marine diesel engines?
- 6.The main starting valve is an element of:
- 7.Through which element of the starting system is the re-starting of the marine diesel engines carried out when compressed air bottles are opened?
- 8.At what minimum temperature in the engine room can the marine diesel engines start-up procedure be started?
- 9.The mean indicator pressure is a direct diagnostic indicator of:
- 10.The strongest influence on the change in the mean indicator pressure is due to:
- 11.Equalization of the mean indicator pressure by cylinders is to be done:
- 12.Maximum combustion pressure is an indirect diagnostic indicator of:
- 13.The greatest influence on the variation of the maximum pressure is:
- 14.Equalization of the maximum pressure by cylinders is to be done:
- 15.An increase in the roughness of the propellers during operation affects mainly :
- 16.The galvanic /electric chemical/ hull protection protects against:
- 17.Which of the listed damages may require the premature scrapping of a marine diesel engine cylinder liner, which has not yet reached the limit of wear?
- 18.Which of the following causes cavitation of cylinder liners and blocks of marine diesel engine?
- 19.When heated to which of the indicated temperatures of the surface of the parts forming the combustion chambers of the mareine diesel engines, the so-called high temperature /vanadium/ corrosion?
- 20.Which of the listed reasons intensifies the wear of piston-cylinder groups of marine diesel engine during their operation on heavy fuel.
- 21.Most engine manufacturers recommend replacing the gaskets between the cylinder head and the cylinder liner every time an engine overhaul is performed. Why?
- 22.It is recommended to adjust the spring tension of the ME nozzles during operation in order to achieve:
- 23.Long-term use of a centrifugal pump with a closed discharge valve leads to:
- 24.What is the purpose of the zinc anodes used on the seawater side of heat exchangers?
- 25.What is the best way to reduce the flow rate of a centrifugal pump?
- 26.Which of the following pumps can be damaged if the delivery valve is closed before stopping the el. motor?
- 27.In the event of a deterioration in the performance of the ME oil cooler, the following actions must be taken:
- 28.Erosive destruction of a tube in the heat exchanger can be a result of:
- 29.A low flow rate accompanied by vibration and noise on the suction side of a centrifugal pump can be the result of:
- 30.In the heat exchanger, when seawater is used to cool fresh water, the seawater pressure must be kept lower than the fresh water pressure. Why?
- 31.A sudden or gradual increase in the chloride content of the cooling fresh water of the ME is a sign of:
- 32.What will we do if the plate cooler leaks after servicing and if we have tightened its connections to minimum values of the quantity A ?
- 33.When cleaning the piston, we should pay special attention to cleaning the grooves of the piston rings. Why?
- 34.What is the periodicity of greasing the bearings of a centrifugal pump?
- 35.The engine revs up to cranking speed but does not start. Why?
- 36.What actions should we take during initial operation of the marine diesel engine with one or more main bearings replaced?
- 37.If the compressor of the refrigeration plant runs for a long time without shutting down, even though it has reached the set temperatures, what could be the reason?
- 38.Which element is used as an alloying element to make cast iron crankshafts?
- 39.Carrying out repairs accompanied by shocks when steam boilers are under pressure are:
- 40.To detect the presence, nature and extent of damage, it is necessary to carry out:
- 41.External examination is done:
- 42.Which of the operations should not be undertaken in the event of a fire in the under-piston spaces?
- 43.What sensors are used to monitor the vibrations of the turbocharger unit?
- 44.Which statement about chemical deaeration is false?
- 45.Which marine steam boilers have the highest boiler water quality requirements?
- 46.Which statement about the order in which boiler water analysis is performed is false?
- 47.Which of the following chemical compounds is a product of the complete combustion of fuel in a ship's main steam boilers?
- 48.At what order is the excess air factor α maintained in automated main ship steam generators?
- 49.When, according to visual methods for determining the quality of the combustion process in marine steam boilers, do we have an optimal value of the coefficient of excess air α?
- 50.What is the cause of the appearance of dark red streaks at the root of the flare ?
- 51.The water level in the level glasses fluctuates and does not stay in a certain position. What is the likely cause?
- 52.Compression pressure is an indirect diagnostic indicator of:
- 53.Compression pressure is a direct diagnostic indicator of:
- 54.When compression pressure is used to estimate engine combustion chamber tightness its current measured values are compared to:
- 55.With the engine in good technical condition, the compression pressure is adjusted by changing:
- 56.What should the graphite structure be in the cast irons some crankshafts are made from?
- 57.What is the main operation in making monolithic /non-composite/cast iron crankshafts?
- 58.After installation, should the radial runout of the pump in the oil sump of the turbocharger unit be checked?
- 59.Structurally, on the compressor side of the turbocharger unit, the modification differences are in:
- 60.Structurally, on the turbine side of the turbocharger unit, the modification differences are in:
- 61.In case of unstable operation of the turbocharger unit, which of the listed actions will not lead to an improvement in the operation of the turbocharger unit?
- 62.How much overloading of the main engine in terms of revolutions is allowed when conducting sea trials?
- 63.The statism of regulatory characteristics is essential for the operation of marine diesel engines at:
- 64.What is the relationship between draft and absolute propeller advance at relative constant operating factors?
- 65.In the oil record book, data is also entered for the following actions in the engine room:
- 66.What is the value of the mechanical efficiency when the engine is running at idle speed?
- 67.Contamination of the working fluid beyond the permissible in volumetric hydraulic drives leads to:
- 68.In which places the use of magnesium protectors for anti-corrosion protection is prohibited:
- 69.The cylinder-piston group of a crosshead marine diesel engine is correctly aligned when the contact between the piston and the cylinder liner is:
- 70.Which of the following causes accelerated wear of the cylinder-piston group of a crosshead marine diesel engine:
- 71.A product of incomplete combustion in a steam boiler is the presence in the exhaust gases of:
- 72.The hardness of the piston ring relative to the hardness of the cylinder liner of the marine diesel engine should be:
- 73.The current compression pressure reference value is determined using:
- 74.The beginning of wear on the first piston ring can be determined using the compression pressure and:
- 75.Wear of two or more piston rings can be determined using compression pressure and:
- 76.An exhaust valve leak can be determined using compression pressure and:
- 77.The purpose of component measurement is to establish:
- 78.What is the purpose of checking the mutual position of the components?
- 79.When is the strength of the parts checked?
- 80.How should the description of the repair report be done?
- 81.What are the instruments and tools needed for a cylinder liner flaw-detection of a marine diesel engine?
- 82.As a result of the uneven wear of the marine diesel engine cylinder liner, what is found?
- 83.What does the number of cylinder liner measurements of a marine diesel engine depend on?
- 84.The results of the measurement of the marine diesel engine piston are recorded in tabular form to determine:
- 85.A cylinder liner has 6 holes for lubrication with cylinder oil. How many clogged holes can you allow the engine to operate?
- 86.When does the air valve of a marine steam boiler open?
- 87.Which indicator diagram gives the most accurate information about compression pressure and combustion onset relative to piston TDC?
- 88.When does the signal of the sensor measuring the pressure of the piston ring against the liner change its direction?
- 89.What is the most common method of determining the area of indicator diagram?
- 90.Where do we get information about standard environmental conditions for a particular marine engine?
- 91.Which value of the angle θ /fuel advance angle/ do we call optimal?
- 92.The best alignment of the ship shaft is achieved by using:
- 93.With prolonged operation of the marine diesel engine, the oil clearance of the main bearings:
- 94.If the total acidity number of the marine diesel engine lubricating oil increases, this can lead to:
- 95.Cast iron valves can be used in piping lines where the fuel has:
- 96.If the water level in a steam boiler drops rapidly and cannot be kept within acceptable limits using standard procedures, you should:
- 97.To avoid fuel spillage when topping up the tanks, you should:
- 98.A sudden or gradual decrease in the pH value or an increase in the sulfate content of the DG cooling system may be a sign of:
- 99.If air got into the refrigeration system, where would you bleed the system?
- 100.When starting an air compressor, the purge valve must be open. Why?