F6 Maintenance and Repair — Management Level — Page 5
507 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 401.When checking and adjusting the position of the cam of the MAN-B&W type MC fuel injection pumps, the piston of the corresponding cylinder should be in:
- 402.The zero of the measuring scale of the device for checking and adjusting the cams and fuel injection pumps of the company MAN-B&W type MC corresponds to:
- 403.The exact type of fuel valve atomizer is listed in:
- 404.When checking and static adjustment of the fuel injection pump of the engine of the MAN-B&W type MC, the rack of the VIT control is in:
- 405.When checking and static adjustment of the fuel injection pumps of the engine company Sultzer type RTA, the cam of the VIT control is:
- 406.The exact number of regulating shims of MAN-B&W type MC fuel injection pumps is indicated in:
- 407.The residual pressure in the high-pressure fuel line is a diagnostic indicator of the tightness of:
- 408.The main engine oil tank level has increased when no new oil has been added. What will you do?
- 409.The results of the analysis of the M/E circulating oil indicated a high tin content. What could be the reason for this?
- 410.Which indicator comprehensively evaluates the state of the kinematics of the main turbo gear unit?
- 411.In order to maintain a half-hour readiness of a turboelectric steam power plant, the turbines must:
- 412.Which of the following operations is not part of the service to bring the turbine to a standstill condition?
- 413.Does the angle of opening of the fuel valve match the static angle of fuel injection of high pressure fuel pump?
- 414.What are "slow" atomizers and when are they used.
- 415.From which part of the ship engine is the largest amount of heat removed with the cooling water?
- 416.What is the reason that pulse turbines have a reduced indicative coefficient of efficiency compared to the potential T/CH of Turbo-piston engines?
- 417.By what percentage does the indicator coefficient of efficiency increase when the S/D ratio increases to values in the range of 2.5 - 4?
- 418.Which of the standard environmental conditions according to: ISO3046/ 1 - 1986 is wrong?
- 419.What are the typical failures and serviceability criteria of ship axles and shafts?
- 420.Which condition must be met for a turbine rotor to be statically balanced?
- 421.Which condition must be met for a turbine rotor to be dynamically balanced?
- 422.Which of the following basic properties of materials for the working surfaces of plain bearings is incorrect?
- 423.Which statement is true regarding the oil film thickness?
- 424.The fuel nozzles are replaced when the wear of the atomizaton holes exceeds the permissible 10% wear of the nominal size:
- 425.The piston group of cross-head engine a is correctly centered when the contact between the piston and the cylinder liner is:
- 426.Which of the following causes accelerated wear rate of the piston group of a cross-head engine?
- 427.The degree of wear of the piston rings is determined by:
- 428.The zero stage of the ship's repair begins when the latter is located:
- 429.The pitting process between the contact surfaces of two workpieces is:
- 430.What action do we have to take if we find out that during ship acceleration the main engine turbine has vibrations?
- 431.Which forced aspiration scheme is primarily used in modern marine main engines?
- 432.What is the difference between turbocharger units of two different size series of the same manufacturer?
- 433.What is the reason for the introduction of size lines of turbocharger units?
- 434.What is the purpose of the different modification of the turbocharger units?
- 435.What do the numbers 631 mean in the turbocharger unit specification designation "VTR 631"?
- 436.The damping properties of the bearing packages are due to:
- 437.The centrifugal shaft-pump lubrication system is a variety of:
- 438.Is the protection by means of magnesium protectors of the turbocharger unit cooling spaces mandatory?
- 439.Can a rotor with welded blades continue to operate with a broken blade?
- 440.What is the turbocharger unit overhaul frequency for a main turbo gear engine?
- 441.When is compressed air supplied to the cylinder?
- 442.What is the organization of the supply of compressed air during start of the marine diesel engine?
- 443.Are four-stroke marine diesel engines started with compressed air?
- 444.What is usually the pressure of the compressed air in the starting air bottles?
- 445.The lubricating oil on the gas side of the turbocharger unit darkens after several hours of operation. What could be the reason?
- 446.After flushing the turbine with water, the turbocharger unit begins to vibrate. What is the reason?
- 447.Air supply from turbocharger unit is not sufficient. What is the reason?
- 448.Why should the main engine rpm be reduced when flushing the turbocharger unit with water?
- 449.What is meant by the term valve and valve seat lapping?
- 450.Why do many engine manufacturers recommend that on the exhaust and intake valves, the sealing surfaces of the valve and seat should be half a degree apart?
- 451.How will continuous operation of the diesel generator at low load affect the overhaul interval?
- 452.When performing a four-stroke engine overhaul, is it important not to swap the intake and exhaust valves?
- 453.When topping up vapor freon, where should the bottle be connected to the refrigeration system?
- 454.What action will we take after we have closed the main start valve and before entering the crankcase?
- 455.Some manufacturers do not recommend washing the compressor part of the turbocharger unit. Why?
- 456.If the ship store is missing original gaskets for assamblig a centrifugal pump, what material will can use?
- 457.Getting small amounts of fuel into the oil leads to:
- 458.Which of the welding methods is suitable for restoring thin-walled parts?
- 459.What is the permissible difference between the opening pressures of the marine diesel engine fuel nozzles?
- 460.Which of the following indicators characterizes the air supply of the engine?
- 461.Which unit controls the opening of the starting air valves?
- 462.The purpose of rotating the crankshaft manually or with a turning gear is to:
- 463.The purpose of the air distributor is:
- 464.What is the number of starting valves in a crosshead engine?
- 465.Starting air valves are operated:
- 466.Is the main starting valve a mandatory element in the engine starting system?
- 467.The connection of the starting air system to the starting air bottles is carried out by:
- 468.Glow plugs are auxiliary devices for:
- 469.When measuring a cylinder liner, we find increased wear. The oil has a prescribed TBN and portion . What actions do we take next?
- 470.Which of the following reasons causes "burning" of the material of the engine's pistons?
- 471.If two diesel generators operate in parallel, the load sharing between them will depend on:
- 472.When painting with compressed air during sea voyage of the ship and unprotected filters of the turbocharger unit, it is possible:
- 473.Why is it important to close all valves in the bilge system after finishing the pumping from engine room?
- 474.If the temperature of the cooling water of a given engine cylinder rises, the reason may be:
- 475.When the nozzles atomization holes are worn out, the coefficient of excess air:
- 476.If pressure appears in the crankcase of trunk piston engines, which we detect when lifting the dipstick for the oil level, the reason is:
- 477.Fretting corrosion occurs as a result of the impact of:
- 478.Which indicators should be measured to obtain the indicator efficiency?
- 479.At constant fuel portion, which of the following increases the most with increasing rpm of the engine?
- 480.As the temperature of the air at the cylinder inlet increases, which of the phases of combustion is reduced?
- 481.Which of the listed methods of pressure charging is used in the new generations of "MAN-BURMEISTER & WEIN" - MC/MCE and "SULZER" - RTA two-stroke engines?
- 482.The constructive feaqture of the pressure charging scheme used in the new generations of two-stroke engines of the companies "MAN-В & W" - MC/MCE and "SULZER" -RTA is:
- 483.In which of the specified design schemes is the load of the bearing units during operation minimum ?
- 484.Which of the following lubrication systems in turbocharged units can be used to lubricate slide bearings?
- 485.Turbine stages of turbocharger units cannot be:
- 486.Leaking fuel injection pump discharge valve causes:
- 487.Which of the following indicators characterizes the wear (tightness) of a high-pressure fuel pump?
- 488.Which of the following indicators can characterize fuel valve wear?
- 489.Which of the following effective parameters can be obtained by direct measurement?
- 490.How do we recognize a leaking fuel injector during testing:
- 491.When aligning the shafts, the permissible limits of displacement and bending are determined by:
- 492.The hardness of the piston ring relative to the hardness of the cylinder liner of the engine should be:
- 493.The wear of the marine diesel engines crankshaft main bearings is determined by:
- 494.The most technologically advanced method for connection of the flanges of two shafts is to use:
- 495.When aligning the shaft during ship repair, the following is taken as a base:
- 496.The best technology for dismantling a propeller is:
- 497.The best alignment of the ship shaft is achieved by using:
- 498.What is the limit of the maximum allowable wear / increase in diameter / of the atomization holes of the nozzles of the engine fuel valves?
- 499.Which of the following causes the material of the engine pistons to burn out?
- 500.Which of the listed causes of damage in various mechanisms is a characteristic of parts joined together with tight and press joints?