F5 Electrical Engineering — Management Level — Page 3
333 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 201.The regulator characteristics of synchronous generators show:
- 202.What is the main disadvantage of iron- nickel vs lead batteries?
- 203.What is the main technical problem of lithium-ion batteries versus lead-acid batteries?
- 204.Unit of measure for what is Lumena (symbol lm) ?
- 205.In which ship electric propulsion systems are three-phase asynchronous motors with double cage rotors used?
- 206.Which malfunction is most common with solenoid valves?
- 207.The idle characteristic of DC generators make it possible to determine:
- 208.What rotation frequency do we call synchronous speed in asynchronous machines?
- 209.In which mode does the current frequency in the rotor of an asynchronous electric motor exceed the frequency of the stator current?
- 210.What information do externals characteristics of synchronous generators have?
- 211.What is the likely cause of the rapid formation of creeping salts on the terminals of an acid battery?
- 212.Which operational factor decisively affects the internal resistance of an acid battery?
- 213.Solar cells are a source of:
- 214.The oscilloscope is a tool for observing the change and measuring:
- 215.The regulatory characteristic of DC generator at constant speed and voltage shows:
- 216.What characteristics determine the performance of DC motors?
- 217.The operating characteristic of a DC electric motor shows:
- 218.Line losses of the power transmission grid can be reduced by:
- 219.How many times the starting current of the asynchronous motor is larger than rated?
- 220.At what power of the ship's power plant can we start induction motor without limiting its starting current?
- 221.From two parallel operating synchronous generators, the generator with a higher voltage will take a larger part of:
- 222.230/380 V is marked on the nameplate of a three-phase Induction motor. How will we connect the phases of its stator winding to connect it to a standard voltage of 380 V ?
- 223.When will a three-phase induction motor not burn if we start it with stators coils connected in star instead of delta ?
- 224.How does the magnitude of the magnetic flux change in the transformer core as the load current increases?
- 225.What should be done to increase the inductive load of a parallel operated synchronous generator?
- 226.Which meter reading error do we define as parallax error?
- 227.Which of the types of charging of alkaline batteries is used only in the case of an absolute necessity?
- 228.For which batteries is intensive gas release characteristic at the end of charging?
- 229.What is the voltage of a nickel-cadmium battery cell in charged condition when measured under load?
- 230.What is the allowable minimum safe voltage of a lead-acid battery cell, measured under load?
- 231.What is the main practical indicator of the correct operation of the selenium rectifier?
- 232.The reactive power that the generator releases on the grid is regulated by:
- 233.The electrolyte of lead-acid batteries is:
- 234.When discharging and charging lead-acid batteries the electrolyte:
- 235.What is the reason for the larger voltage in one of two parallel operating the generators where the power in kilowatts is divided equally?
- 236.What determines the power factor cosφ of a generator to the main switchboard /MSB/ buses during single operation?
- 237.If out of two generators operating in parallel at 80% load, one fails, what will be our immediate actions?
- 238.What does the decrease in speed and stop the rotation of the synchronoscope pointer mean during a procedure of paralleling two generators ?
- 239.In the cascade principle of automatic control, which of the two controllers should be set up first?
- 240.Why is it especially important that the sensor and transmitter are installed in the right place on the ER systems?
- 241.The temperature sensor is marked Pt 100 - what does that mean?
- 242.The range of the transmitter is from 0 to 200 Bar, and the value of the output signal - from 4 to 20 milliamps. How much will the signal be at 100 Bars?
- 243.What happens if generators 1 and 2 operate in parallel and generator 2 prime mover runs out of fuel, ?
- 244.After successfully paralleling two generators, power distribution and equalization of their active and reactive load is done by:
- 245.The device with which diodes are checked is called:
- 246.What device will we use to detect a grounding problem with a 24 Volt DC circuit?
- 247.PT-100 sensors sometimes have 3 or even 4 connecting wires - why?
- 248.During a routine check of the functions of the alarm system several se points values are lost. What is the correct way to recover them?
- 249.How many volts per cell should we supply when slowly charging lead acid batteries?
- 250.What is the correct order of operations which the Remote Automatic Control system will conduct in an emergency with certain automatically controlled mechanisms?
- 251.What do we mean by "scope of the instrument"
- 252.What is the output signal from NiCr-Ni thermocouple?
- 253.What would indicate a transducer scale problem?
- 254.Before measuring insulation with a megohmmeter, the windings of large electrical machines should be grounded for about 15 minutes before the start of the measurement because:
- 255.External shunt resistance at ammeter measurements are sometimes used to:
- 256.A resistance of unknown value can be checked/measured using the voltmeter-ammeter method. How should the two appliances be connected to the resistance?
- 257.An incidentally occuring low resistance accompanied by the flow of abnormally high values of current is known as:
- 258.What precaution should be taken during fault detection measurements with a simple solenoid type mechanical voltmeter?
- 259.With what device can the insulation resistance of the ship's electrical equipment be measured?
- 260.A high impedance multimeter should be used when troubleshooting electronic equipment. Why?
- 261.The measuring instruments of a three-phase generator show 450 V, 300 A and 163.6 kW at cos φ = 0.7. How much will the readings of the wattmeter increase at cos φ = 0.8?
- 262.In the terminology of measuring processes, the values which can change without particular increase certain parameters (e.g. temperature, pressure or level) are called:
- 263.When measuring insulation with a meggerohmmeter, as a result of the continued rotation of its handle, the gradual increase in the readings of the measuring poiinter is result of:
- 264.What defines the "sensitivity threshold" characteristic?
- 265.If the revolutions of the synchronous diesel genetator connected to the buses drop by 10% due to a problem in the regulator, what consequences will that have on the electric motors currently operating?
- 266.What are the main elements of which contactless electrical control and protection apparatus are built?
- 267.Which mechanism is most prone to breakdown in direct current electrical machines?
- 268.What is the most efficient way to change the rotation frequency to asynchronous electric motor?
- 269.When does the capacity of the batteries change?
- 270.What is the main reason for the occurrence of short circuits?
- 271.On some diesel-electric ships the direct current propulsion electric motor reaches only half of its revolutions/speed/ when the generator is fully excited. Revolutions greater than these can be reached via:
- 272.How many amperes is the current of a power diode in three-phase rectifier if the load current is 60 A
- 273.What is the difference between active and key mode operation of transistors?
- 274.The use of 4 diodes in the circuit of a full-cycle bridge rectifier will:
- 275.Which of the following statements regarding analog and digital devices is true:
- 276.An electrical device/element that most often uses the electromagnetic principle induction is a:
- 277.Output voltage 440 V of an alternator is maintained by:
- 278.Why is a DC motor started through starting resistors?
- 279.What is the reason for buzzing without spinning after starting of an otherwise mechanically fit asynchronous electric motor?
- 280.Which of the following applications is not inherent to diodes?
- 281.At a maximum voltage of 15 Volts, a 3 Watt Zener diode can safely work with current up to:
- 282.How does the integrating function affect the performance of the controller?
- 283.What is the difference between a THERMOSTAT and a TEMPERATURE TRANSDUCER?
- 284.What are the first steps in Black-Out situation?
- 285.The control properties of induction motors are represented graphically by:
- 286.What electrical power is measured in VARs (Volt-Amps Reactive)?
- 287.What electrical power is measured in VA (Volt-amperes)?
- 288.What electrical power is measured in W (Watts)?
- 289.Why should the starting resistances of a DC electric motor operating in a steady-state mode be disconnected?
- 290.Grounding an electric motor can be defined as a connection between its casing and:
- 291.During the operation of an AC generator connected to the grid, the change in electrical load and "cos φ" corresponds to a corresponding change in the armature reaction. Compensating for the change in armature reaction is achieved through
- 292.In the case of a failure (e.g., fuel supply interruption) of one of the primary movers in parallel-operating generators,the following will happen:
- 293.A direct current flowing through a conductor wound around a soft iron core is a description of a simple:
- 294.When voltage is applied to resistors connected in series, how will the voltage be distributed across the resistors?
- 295.If a command is given to start an asynchronous motor, but it only buzzes and does not rotate, what should be done?
- 296.How is battery charge level properly monitored?
- 297.How is the active load distributed between parallel-operating synchronous generators?
- 298.Why should the battery compartment be ventilated?
- 299.Which protection of the steering drive causes the electric motor to be switched off:
- 300.Which protection of an asynchronous motor is also known as "self-starting protection"?