F5 Electrical Engineering — Management Level — Page 2
333 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 101.Which statement is false regarding the power factor?
- 102.Which of the following sensors is not a generator?
- 103.Which of the listed regulators has residual error?
- 104.Which of the following devices is a comparator?
- 105.Which statement about fluorescent lighting is not true?
- 106.In which type of lighting cosφ /power factor / is highest?
- 107.Immediately after connecting two generators in parallel, you must:
- 108.At what point will we close the ACB of the incoming generator to connect it in parallel to the MSB busbars?
- 109.The energy required to excite a 3-phase synchronous generator is provided by:
- 110.What is an analog signal?
- 111.A semiconductor that decreases its resistance when the temperature increases is:
- 112.Which of the listed sensors have a reversible action?
- 113.Which definition of selsins does not fit into the functions they perform?
- 114.The silicon rectifier is fixed device used to change:
- 115.At which regulation of marine induction drives the quality of process is the highest?
- 116.How do we define reactive power?
- 117.How can the direction of rotation of a three-phase asynchronous electric motor be changed?
- 118.Increasing the excitation of the generator in a diesel-electric propulsion system will cause the DC propulsive motor to:
- 119.What needs to be done to increase the active load on a parallel-operating synchronous generator?
- 120.The voltage generated by most alternating current (AC) generators is supplied from the generator to the busbars through:
- 121.The lagging of the rotor in an asynchronous motor behind the rotating magnetic field is characterized by:
- 122.An alternating current motor that uses a rheostat to change the frequency/rotational speed is called:
- 123.In which type of asynchronous motor is it possible to use a star/delta starter?
- 124.When a command is given to change the rotational frequency of a multi-speed asynchronous motor, what changes in the motor?
- 125.Why is the starting current limited in direct current (DC) motors?
- 126.In order to provide a larger current, batteries are connected:
- 127.How do we define the apparent power of electrical circuits?
- 128.On which functional dependence are the derived characteristics of ship electric propulsion systems based?
- 129.What are the disadvantages of alternating current (AC) brushed motors?
- 130.Is it possible to reverse the asynchronous micromotor with shielded poles?
- 131.The advantages of using contactors for controlling electric drives are:
- 132.The factor determining the frequency (Hz) of an alternating current generator is:
- 133.The different resistances in the rotor circuit of an induction motor with a wound rotor are used for:
- 134.The connection of three-phase windings in a "star" configuration is denoted by which symbol?
- 135.Which of the following statements is true for all three-phase alternating current generators?
- 136.The purpose of compensating windings in synchronous electric motors is to:
- 137.The method used to maintain equal load sharing between two separately excited DC generators operating in parallel is:
- 138.What is the reverse power protection of a synchronous generator?
- 139.What is Selective Load Tripping protection of the marine power plant?
- 140.Where does the name "zero protection" of self-start protection come from?
- 141.How many interconnected machines are included in the control scheme of DC motor drives in a "generator-motor" system?
- 142.What is the main requirement for the functional converter and the control system in frequency control systems for asynchronous drives?
- 143.When rating motors for electric drives, the most difficult check is performed for:
- 144.Which batteries exhibit the "memory effect" the most?
- 145.What does Kirchhoff's first law state?
- 146.Which of the listed motors is designed for small power applications (up to 150 W)?
- 147.When operating under conditions of unusually high, low, or continuously fluctuating temperatures thermal breakers are required to have a compensating element for the surrounding environment. This element is:
- 148.What is the main difference between a relay and a contactor?
- 149.The number of cells in a 12V lead-acid battery is:
- 150.The switch and the fuse have a similarity because both can/will:
- 151.The purpose of the commutator/collector and brushes of a direct current generator is to:
- 152.What is the type of magnetic field in a single-phase induction motor with a starting winding?
- 153.Which type of rotor is active-reactive
- 154.Is there a transformer with only one winding (primary) from which a tap-point terminal is made?
- 155.Which types of DC motors should not be started without load?
- 156.What is true and applies to a multi-phase propultion motor?
- 157.The overload protection of the steering electric drive
- 158.Which device prevents an action (e.g., "start") until the necessary conditions for it are met?
- 159.What is the main advantage of starting an induction motor with a wound rotor using a rheostat?
- 160.Which of the listed electrical machines has the most limited application?
- 161.If two inductive consumers L1=6 H and L2=12 H are connected in parallel in one electrical circuit, how much will be the total inductance L/S/ ?
- 162.What law do direct acting rev regulators follow?
- 163.The two main sources of emergency electrical energy are:
- 164.When the load is removed from the shaft of a synchronous electric motor its revolutions will:
- 165.Which of the following can cause a cargo winch to operate below normal revolutions at medium-high constant load:
- 166.The dielectric strength is:
- 167.Sulphation of the plates of an acid battery is prevented by:
- 168.What is the practical way to find out if а DC motor is overloaded?
- 169.Which element of electronics replaces the transformer with a factor of transformation equal to one?
- 170.For what purpose is a delay introduced on the generator circuit breaker trip when a short occurs?
- 171.Why DC motor with series excitation should not be allowed to idle?
- 172.How can the algorithm of operation of a Programmed Logic Controler be changed?
- 173.Manual overide of the motor overload protection is provided in the control of which electric drive?
- 174.To which parameter does the sound and light alarm signaling for power failure of each of the navigation lights react?
- 175.The storage battery must withstand an emergency load without recharging with a voltage within the limits of:
- 176.Which winding in DC machines do we call leafy?
- 177.What is reactance in AC circuits?
- 178.What law of regulation will be used in a hydraulic system with droopless amplifier and constant feedback ?
- 179.What law of regulation will be used in a hydraulic system with droopless amplifier and flexible (isodromic) feedback?
- 180.How do clearances in the lever system between the governor and the fuel rail affect the operation?
- 181.Which of the listed parameters allows for the most complex regulation of the engine?
- 182.How does the current through the AC contactor coil depend on the air gap value in the magnetic system ?
- 183.Can a continuous-duty electric motor be used in short-time duty or intermittent periodic duty term mode ?
- 184.Bipolar transistors are controlled by:
- 185.Unipolar transistors are controlled by:
- 186.The external characteristic of a DC generator is a functional dependence of:
- 187.The contactor is a control device with two stable positions (opened and closed), whose emergency actuation is:
- 188.In which of the following accidents the DC generator can give higher but also lower than normal voltage?
- 189.How do we define a signal as digital?
- 190.Resistance is marked with three reds strips. How many ohms is that?
- 191.When is the common collector scheme used with bipolar transistors?
- 192.For which of the listed systems will a PID controller be installed?
- 193.Which of the following letter combinations define a flow indication controller in the process diagram or in the instrumentation diagram?
- 194.Some of the electrical equipment may be marked with the symbols Ex i. What do they mean?
- 195.How many times will the heat load on the stator windings increase if the current load on an asynchronous generator is doubled?
- 196.What is included in the re-testing conducted at the end of the sea trials of the electrical equipment?
- 197.Which of the listed devices is subjected to special tests during sea trials?
- 198.Which of the listed documents is in the list of technological documents of the electrical equipment of the ship?
- 199.What is the main, most important problem of the ship's Integrated and Alarm Monitoring and Control(IAMCS) automation?
- 200.What is the most serious problem before the automatic synchronization of the ship's synchronous generators?