F6 Maintenance and Repair — Operational Level
239 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 1.When reducing the angle of fuel injection timing with purpose to equalize the maximum pressure (Pz) in the engine cylinders, what condition should be taken into account?
- 2.A crack in the cylinder head of a marine diesel engine may most likely result from:
- 3.A fuel start may be optimal for:
- 4.A high pressure setting of an opening of the fuel oil injection valve causes ?
- 5.After how many working hours, TC bearings should be replaced, even if all of their working parameters are normal?
- 6.At the expense of which parameter are newer generations of Ship Internal Combustion Engines less sensitive to wear on their piston-cylinder groups?
- 7.By changing the cross section at the outlet of the nozzle what position can be changed?
- 8.By clarification mode we mean a mode in which basic we separate?
- 9.By periodic monitoring of the “breathing” of the crankshafts of Ship Internal Combustion Engines we can establish the:
- 10.Can fuel separation replace (fuel) filtration?
- 11.Can the four stroke engines be reversible?
- 12.Change over from distilled fuel to heavy fuel oil and vice versa is done at a lower than the nominal loads of the engine in order to:
- 13.Checking and static adjustment of the Main engine fuel oil injection pump is done by data from?
- 14.Compression pressure is an indirect diagnostic indicator of:
- 15.Condensate overcooling is?
- 16.Contamination of the working fluid in the hydraulic system above the permissible levels results in:
- 17.Data for the following operations carried out in the engine room are also recorded in the oil record book :
- 18.Due to inspection or repair, the boiler must be emptied. If we have enough time, how will we conduct this operation?
- 19.During discharging bilge water from bilge tank through bilge separator (oily water separator), when the level in а tank reaches the border between water and oil residue, what will be your correct actions?
- 20.During a voyage, when painting with an air gun close to unprotected turbocharger filters, it is possible to:
- 21.During boiler operation it is found that a water levels not visible. When the boiler Is blown down the water level is noticeable and immediately increases. What is the reason?
- 22.During the preparation for the operation of the turbine system, the engineer of the watch must record in the engine log book:
- 23.Erosive destruction of a tube in the heat exchanger can be a result of:
- 24.Faster fuel oil change-over from light fuel oil (MDO) to high fuel oil (HFO)can cause ?
- 25.Filters used in shipping are usually made:
- 26.From a thermodynamic point of view, engine cooling:
- 27.Fuel filters are:
- 28.Fuel oil heating steam pressure should not exceed:
- 29.Fuel systems servicing the Main engine are:
- 30.How do the clearances in the lever system between the governor and the fuel rack affect the operation of the engine?
- 31.How is the engine starter connected to the crankshaft?
- 32.How many degrees ºС do we need to raise the temperature of the superheated steam to increase the boiler efficiency by 1%?
- 33.How many times will the thermal load on the stator coils increase if the current load of an asynchronous generator is doubled?
- 34.How much can the limit pressure of the counter-steam be increased when the steam turbine is reversed?
- 35.How should the separator be operated in order to obtain the best separation results?
- 36.How the roller bearings are calculated by?
- 37.How we recognize the leaking nozzle tip during a stand test?
- 38.How will we protect the boiler from corrosion in case of prolonged inactivity?
- 39.How will you mount a ball bearing to the centrifugal pump shaft?
- 40.If a hydraulic pump on a hydraulic winch overheats the cause could be?
- 41.If a trunk Ship Internal Combustion Engine has been in operation for 24 hours without separating its lub. oil, when switching on the separator, what between-flushing time period must be selected?
- 42.If maximum fuel oil supply pressure is used in diagnostics, we need the values for:
- 43.If the alkalinity of the boiler water is P = 450 PPM calcium carbonate, what will be the appropriate action?
- 44.If the boiler water level drops rapidly and cannot be kept within the permissible limits using standard procedures, we must:
- 45.If the boiler water salinity is 500 PPM, what action should be taken?
- 46.If the color of the surface layer of the main bearing white metal is black and of high hardness and there are scratches on the crankshaft journal, what is the probable reason?
- 47.If the cooling water temperature at the outlet of the auxiliary engine is lower than normal, the most likely cause is
- 48.If the total acidity of the lubricating oil of the ICE increases, this can lead to:
- 49.If there are no original gaskets for the centrifugal pump, what material should be used for making a new gasket?
- 50.If there is a pressure in the crankcase of the trunk piston engine, which is detected by raising the oil level plug, the reason is:
- 51.In case of unstable operation of the turbocharger unit, which of the following actions will not lead to an improvement in the operation of the turbocharger?
- 52.In order to avoid fuel oil spill when filling the tanks:
- 53.In order to maintain а half-hour readiness of a turboelectric steam generator,
- 54.In what range should the current be found under normal acid battery charging 12V 160Ah?
- 55.In which of the aforementioned accidents can the DC generator produce higher and lower than normal voltage?
- 56.In which of the following cases the DC generator can generate higher or lower voltage than the normal?
- 57.Incomplete combustion in a steam boiler is indicated by the presence in the exhaust of:
- 58.Inspection and setting up of static adjustment of high pressure fuel pump of ICE is performed according to data from:
- 59.It is important to follow the maintenance order for the purifiers . Why?
- 60.Low opening pressure of the fuel valve causes
- 61.Marine engine operates with black smoke. Why?
- 62.Maximum fuel injection pressure is a diagnostic indicator of:
- 63.Mean indicated pressure is a direct diagnostic method for?
- 64.Mechanical efficiency depends on:
- 65.Non-hermetic injection valve on the fuel pump causes:
- 66.Oil entering the ICE water cooling system will cause:
- 67.Oxygen content in condensate mustn’t exceeds:
- 68.Prior to starting the boiler burner, which of the above actions is most important?
- 69.Prolonged operation of a centrifugal pump with a closed discharge (delivery) valve results in:
- 70.Provided the technical condition of the engine is sound, the compression pressure is regulated by:
- 71.Purification mode means a process of operation in which
- 72.Reduced fuel pressure after opening the fuel valve can be caused by:
- 73.Reduction of the maximum fuel oil supply pressure can be caused by?
- 74.Removal of the scale from steam boilers in operation is done by:
- 75.Resistance of unknown value can be checked / measured using the voltmeter-ampermeter method. How should the two devices be connected to the resistance?
- 76.Roller bearings are selected according to their
- 77.Ship’s purifiers are mostly?
- 78.The API oil classification defines with English letters:
- 79.The auxiliary boiler safety relief valve must:
- 80.The beginning of fuel injection can be optimal for:
- 81.The boiler water gauge glass must be blown down periodically in order to:
- 82.The crankshaft deflection gives information about:
- 83.The current reference value of compression pressure is determined by:
- 84.The damping properties of the bearing packages are due to:
- 85.The damping properties of the bearing packages are due to:
- 86.The electric starter is:
- 87.The engine spins to starting rpm, but does not start. Why?
- 88.The exhaust gas boiler operation during low engine loads result in low-temperature corrosion of the heating surfaces. This is due to the presence of:
- 89.The function of the starter in the starting system is:
- 90.The heat intensity during heavy fuel oil operation with higher heating temperature is?
- 91.The high opening pressure of the fuel valve (injector) can be caused by:
- 92.The Increase of crankcase pressure in trunk-piston engine indicates:
- 93.The leakage of the exhaust valve can be determined by the compression pressure and:
- 94.The load at which the bearings can withstand 1 million revolutions without showing signs of pitting in the work bodies or rings determines:
- 95.The low opening pressure of the fuel valve can be caused by:
- 96.The maximum fuel oil supply pressure is a diagnostic measure for?
- 97.The number of measurement points in the cylinder liner of the main engine depends on:
- 98.The oil pressure is normal when starting the engine. When the engine is loaded, as its temperature increases, the pressure decreases due to:
- 99.The oil record book also records the following information in the engine room:
- 100.The overcooling of the condensate is: