F6 Maintenance and Repair — Operational Level — Page 2
239 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 101.The oxygen content of the condensate water must not exceed:
- 102.The periodic monitoring of the crankshaft deflection reveals:
- 103.The permissible water content of marine fuel
- 104.The plate of the three-phase asynchronous electric motor is marked 230/380 V. How will we connect the phases of its stator coil for its connection to a standard voltage of 380 V?
- 105.The pressure of the fuel heating steam shall not exceed:
- 106.The product of incomplete combustion in a steam boiler is the presence in the exhaust of:
- 107.The purpose of the planned maintenance system is:
- 108.The purpose of the starter in the starting system
- 109.The ship’s compartment where a batteries are charged should be well ventilated because during charging a gases which are discharged are?
- 110.The ship’s settling tanks are part of?
- 111.The start of wear of a first piston ring can be determined by the compression pressure and:
- 112.The strongest effect on the change in the mean indicator pressure is due to:
- 113.The temperature of oil which flows in turbocharger bearings should be
- 114.The temperature of the exhaust gas of the cylinder of the Ship Internal Combustion Engines is high. Why?
- 115.The transition from diesel oil to heavy fuel and vice versa is made at a load lower than the nominal in order:
- 116.The transition from heavy to diesel oil should be done:
- 117.The water economizer increases the boiler efficiency by utilizing heat from the exhaust gas after the boiler. In order to increase the temperature of the feed water by 1ºC, it reduces the temperature of the exhaust gas by:
- 118.The water level in the boiler sight glass is unstable and does not stay in the certain position. What is the probable reason?
- 119.To avoid fuel spills when filling tanks, you must:
- 120.To what extent can the back-steam pressure be increased during steam turbine reversing?
- 121.Under the term "lapping" of valve to the valve seat we understand
- 122.Under the term water seal of the separator we understand?
- 123.Under what conditions is an external characteristic obtained?
- 124.Usually, boiler water sample is taken?
- 125.We should pay special attention to the cleaning of the piston ring grooves while cleaning the piston. Why?
- 126.Wear down of the main engine crankshaft is measured by :
- 127.What action is needed if the boiler water pH is below 7?
- 128.What action will we take in case of vibration of the turbine when the ship is accelerating?
- 129.What actions are necessary to be taken if the boiler water pH > 11?
- 130.What actions shall we take after we close the main starting valve prior to entering into the crankcase?
- 131.What actions should be taken during initial operation of the ICE with one or more main bearings replaced?
- 132.What actions will you take if the pH of the boiler water is below 7?
- 133.What actions will you take if the pH of the boiler water is more than 11?
- 134.What can be caused during the rapid change over from distilled to heavy fuel:
- 135.What can be the percentage of the exhaust gas temperature deviation between the cylinders?
- 136.What does the mechanical efficiency depend on and how?
- 137.What happens in case of a phase insulation breakthrough to the body of an electrical machine connected to a three-phase network without a zero conductor and an insolated star center?
- 138.What is the biggest drawback of the belt gears?
- 139.What is the daily fresh water consumption we should guarantee when planning the voyage?
- 140.What is the difference between the nozzle guide vanes of steam and gas turbines?
- 141.What is the main problem in the Marine Boiler hydraulic tests, conducted without disassembling the piping?
- 142.What is the main problem with the hydraulic tests of the boiler conducted without dismantling the valves?
- 143.What is the main purpose of lower blowdown of the boiler?
- 144.What is the main purpose of the Ship Steam Boiler's gas analysis?
- 145.What is the main reason of improper steam boiler circulation?
- 146.What is the main type of corrosion in an exhaust gas steam boiler?
- 147.What is the minimal Engine Room temperature that allows the starting of the Marine Internal Combustion Engine (ICE)?
- 148.What is the most appropriate oil sampling site for ICE analysis?
- 149.What is the organization of compressed air supply when starting ICE?
- 150.What is the percentage of start-up revolutions compared to the nominal ICE revolutions?
- 151.What is the reason for an asynchronous/induction (squirrel) cage motor to be humming/buzzing but not turning (when connected to the (power) grid), provided that the electric motor and the (power) grid are mechanically sound:
- 152.What is the reason for the crankcase oil to become "milky"?
- 153.What is the reason for the damages caused by cavitation on the cylinder liners of a internal combustion engines?
- 154.What is the recommended permissible metal temperature for the Ship Internal Combustion Engines fuel valve sprayers?
- 155.What is the rule for performing turbine noise inspection?
- 156.What is the value of mechanical efficiency when idling the engine?
- 157.What kind of countermeasures will you take if the pH factor of the boiler water is under 7?
- 158.What kind of instrument can measure the insulation resistance of marine electrical components?
- 159.What preventive action should we take as a matter of priority before preheating the turbine?
- 160.What should be the density of the electrolyte in order to stop the charging of the alkaline batteries?
- 161.What should be the structure of the graphite in the cast iron, from which some crankshafts are made?
- 162.What should we do if the plate type cooler is leaking after maintenance, if we tightened the inspection cover to minimum distance of A?
- 163.What type of roulette should not be used when measuring the cargo level in light cargo tanks or dehydrated crude oil during the loading process?
- 164.What will be the effect of the continued work at low load on the overhaul interval of the main engines?
- 165.When air compressor maintenance is complete and we are ready for trial run, it is important to
- 166.When can steam from auxiliary turbine be used in the main turbine unit?
- 167.When can steam from auxiliary turbomachines be used in the main turbo gear unit?
- 168.When checking the fuel supply phases, which of the methods for regulating the cycle portion of the high pressure fuel pumps requires to fix the control body in a specific position ?
- 169.When cleaning a four-stroke engine, is it important not to change the intake with the exhaust valves and vice versa?
- 170.When cleaning the piston, the grooves for the piston rings should also be cleaned . Why?
- 171.When cooling sea water centrifugal pump delivery pressure is increased, probably cause can be ?
- 172.When discharging with the oily bilge water separator, we reach the oil level in the bilge tank. What actions do we take?
- 173.When is cavitation possible in the steam boiler down-comer (water) tubes?
- 174.When is cavitation possible in the drainage pipes of watertube boilers?
- 175.When is it dangerous for the fuel supply pressure to be higher than normal after opening the fuel valve?
- 176.When is it possible for cavitation to occur in the downcomer pipes of the water tube boilers?
- 177.When operating on heavy fuel with a higher heating temperature, the heat intensity is:
- 178.When reducing the angle of fuel injection timing in order to equalize the maximum pressure (Pz) in the engine cylinders, what condition should be taken into account?
- 179.When should you open the air ventilation valve of steam boiler?
- 180.When the engine is in good working order, the compression pressure is adjusted by changing:
- 181.When the maximum fuel pressure is used in the diagnostic process it is necessary to have equality between:
- 182.When the temperature of the nozzles is higher than 180 °C there is a possibility of:
- 183.When the temperature of the sprayers is hgher than 180 ºC, there is a likelihood of:
- 184.Where can we find information about standard environmental conditions for a particular marine engine?
- 185.Where do we get information about standard ambient conditions for a particular ship’s Main engine?
- 186.Which change in the listed operating parameters will cause the temperature of the superheated steam to increase?
- 187.Which condition must be met for the rotor to be dynamically balanced?
- 188.Which condition should be satisfied for the rotor to be statically balanced?
- 189.Which indicator parameters should be measured in order to obtain the indicator efficiency?
- 190.Which injection angle (beginning of injection), measured on the crankshaft, do we define as nominal?
- 191.Which insulation resistance of an electric machine is considered normal during operation?
- 192.Which is the main way for starting high speed Marine Internal Combustion Engines?
- 193.Which is the most common reason for overheating of the main bearings:
- 194.Which of the principles below is applied during Marine Boiler heat transfer?
- 195.Which of the answers is correct, if the chlorids in seawater reach 50 PPM
- 196.Which of the below actions are not part of the procedure for turbine standstill mode?
- 197.Which of the below actions is of greatest importance when starting the boiler burner?
- 198.Which of the below evaporators are used as elements of the marine fresh water generator plants?
- 199.Which of the following can cause the overheated steam temperature to rise in the boiler?
- 200.Which of the following causes „Burnout” of the Main engine pistons material?