F1 Electrical, electronic and control engineering — ETO (CMKE, Poland) — Page 4
586 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 301.The direction of action of the electrodynamic force is determined on the basis of:
- 302.Electromotive force induced in the armature winding depends on:
- 303.In a shunt DC motor:
- 304.In a series-wound DC motor:
- 305.The rotor of a squirrel cage motor is:
- 306.The rotor of a wound-rotor motor is:
- 307.The critical slip in an asynchronous squirrel cage motor:
- 308.Torque overload of an asynchronous motor should be:
- 309.Synchronous speed means:
- 310.Synchronous speed can be calculated on the basis of the following formula:
- 311.A synchronous machine with a 4-pole magnet operating in the network with the frequency of 60Hz has the shaft speed of:
- 312.The change of rotation direction of an asynchronous motor shaft occurs through:
- 313.A slip in an asynchronous motor corresponds to:
- 314.Asynchronous squirrel cage motors during start-up:
- 315.In a synchronous generator, a rotating rectifier:
- 316.The regulation of reactive power in a synchronous generator is achieved by means of:
- 317.The distribution of active power upon parallel operation of synchronous generators:
- 318.The distribution of reactive power upon parallel operation of synchronous generators:
- 319.Directional protection (from inverse power) of a synchronous generator prevents:
- 320.Electromotive force induced in the armature of a synchronous machine depends on:
- 321.Which of the following items are most frequently used within the generating set:
- 322.Which of the following can be used as a shaft generator:
- 323.If a synchronous machine is used as a shaft generator, it is necessary to:
- 324.When incorporating a synchronous generator to work in parallel, it is necessary to:
- 325.The rotational speed regulator of a motor driving a synchronous generator serves for:
- 326.Limit power angle in a synchronous generator is related to:
- 327.What conditions the occurrence of the reluctance torque in a synchronous generator:
- 328.The regulation of the rotational speed of an asynchronous squirrel cage motor can be performed by means of:
- 329.The regulation of the rotational speed of an asynchronous wound-rotor motor can be performed by means of:
- 330.An asynchronous double squirrel cage motor is characterised by:
- 331.A critical slip in an asynchronous machine may be regulated:
- 332.The designation of connection groups in a 3-phase transformer defines:
- 333.In the case of parallel operation of 3-phase transformers, the following items must absolutely be equal:
- 334.Impedance voltage of the transformer is:
- 335.The change of voltage in the transformer depends on:
- 336.The enclosed drawing shows a block diagram of the closed adjustment system. The item marked with X represents:
- 337.The serial correction unit attached to the multi-inertial control object is intended to increase the phase reserve. This can be achieved with the correction module
- 338.The following is called the cascade control system:
- 339.The follow-up control system is called a system in which:
- 340.The measuring line in the closed-circuit feedback circuit shall include:
- 341.Calibration of the measuring transducer refers to:
- 342.Output signal is not delayed with respect to the sinusoidal input signal in the:
- 343.The displayed response to the step function relates to the following element:
- 344.The displayed response to the step function relates to the following element:
- 345.The displayed response to the step function relates to the following element:
- 346.In a cascade control system:
- 347.The MRAC (Model Reference Adaptive Control) adaptive control system uses a reference model which:
- 348.Adaptive adjustment with intermediate identification is based on the fact that:
- 349.Control deviation
- 350.The transmittance of the controller is:
- 351.Which of the closed circuits will certainly be unstable It will be a closed circuit
- 352.Which of the closed circuits with negative feedback listed below will be stable for sure? It will be the one whose open layout
- 353.The transmittance of the open circuit is equal to Go(s) = K/(s³ + 2s² + 4s + 2). At what gain K of the open circuit will this circuit, after closing the unity negative feedback loop, be at the stability limit?
- 354.The following diagrams show the Bode plot of the open system. On the basis of this, it is not possible to determine that the reserve of the phase Δφ and the reserve of the module ΔM of the closed circuit, i. e. after the feedback loop is closed, will be as follows
- 355.Using the following step characteristic of the PI controller for individual excitation, determine the following values: amplification factor kp , integration time constant Ti, proportionality range Xp:
- 356.Switching on the auto-tuning function in the controller allows for:
- 357.When selecting the controller settings by Ziegler-Nichols method, knowledge of the following is required:
- 358.Spectral transmittance G(jω) is created from operator transmittance G(s) y substituting the following expression for the operator Laplace s:
- 359.The deviation of regulation e(t) = 2·1(t) was put on the PI controller input and on the serial-parallel structure with KP = 2 and KI = 0.5 settings. What value will the control signal reach after 6 seconds from the occurrence of the adjustment error, assuming that the deviation value will not change, because the system had an interrupted feedback
- 360.The automation element is described in the following differential equation: 𝑇𝑦̇ + 𝑦= 𝑘𝑢
- 361.The closed-circuit control system with PI controller and linear object is placed at the limit of stability, and a sinusoidal vibration is generated at its output with a constant amplitude and frequency. To increase oscillation damping and thus reduce overregulation and shorten the adjustment time, it is necessary to:
- 362.The automation element is described in the following differential equation: 𝑇𝑦̇ + 𝑦= 𝑘𝑢 The status matrices of this element are as follows:
- 363.Dominant poles of the closed-circuit system
- 364.Two amplifiers: one with 10 V/V amplification and the other with 2 V/V amplification are connected in series. The total total amplification shall be:
- 365.The lengths of the double-sided lever arms are x and y. When the arm x is affected by the input force Fx the arm y is affected by the force Fy. The amplification ratio of this lever is:
- 366.The oil damper (mass with spring running in a viscous medium) has the following characteristics:
- 367.The differentiating-integrating adjustment called PID correction
- 368.Moving the transmittance poles of a closed circuit with available measurement variables is
- 369.The astatic system in relation to the given value is called the system
- 370.In order to be able to synthesize a system with any pole position and thus any dynamic properties, it is required that:
- 371.The amplifier with a very high amplification factor was covered by a negative feedback loop with transmittance G (s). What is the transmittance of the entire system?
- 372.Transmittance of the PD acceleration module is equal to:
- 373.Adjustment of the adjustment system by means of a proportional element:
- 374.Extreme control systems can therefore be achieved by adding an optimization module to the basic control system. Its task is to:
- 375.An integrating and differentiating compensator (lead-lag compensator) has the following transmittance (1 + 𝛼𝑇𝑠)/(1 + 𝑇𝑠) . It is differentiating for:
- 376.Discrete transmittance T (z) of the system is:
- 377.Discrete transmittance T (z) can be obtained from continuous transmittance T (s) by the following substitution (Ts means sampling time):
- 378.Discrete transmittance T (z) can be obtained from continuous transmittance T (s) by substitution Ts means sampling time):
- 379.Discrete transmittance T (z) can be obtained from continuous transmittance T (s) by substitution Ts means sampling time):
- 380.Are the courses of the step characteristics plotted for discrete transmittance obtained from continuous transmittance and the step characteristics obtained for this continuous transmittance the same::
- 381.There is given the following discrete transmittance: 𝐺(𝑧) = 5/(10𝑧−2). In the input signal path, a signal delay block has been set for 3 sampling periods. Now the discrete transmittance is as follows:
- 382.There is given the following discrete transmittance of a certain system: 𝐺(𝑧) = 5/(10𝑧−2). Is it the system stable?
- 383.Transmittance of the discrete object is equal to 𝑃(𝑧) = 1/(z(𝑧−2)) , and the controller to 𝐶(𝑧) =k. Transmittance (output-input) of the closed-circuit control system consisting of these elements shall be equal to:
- 384.The characteristic equation of the discrete adjustment system is as follows: 𝑧2 + 0,1𝑧−0.72 = 0. The system is:
- 385.Discrete PID controllers can implement either positioning or incremental algorithm. An incremental algorithm is used when:
- 386.Discrete PID controllers can implement either positioning or incremental algorithm. The positional algorithm is used when:
- 387.The settings of the discrete PID controller are:
- 388.The discrete control system is stable when its characteristic equation 1+Gopen(z)=0:
- 389.If an integration element with delay is introduced in series into the open circuit, then in this system:
- 390.In the adaptive control system with gain scheduling
- 391.The diagram on phase plane:
- 392.Phase plane graphs are used to illustrate the performance of the following systems:
- 393.Step control system is a system containing:
- 394.The method of presenting the properties of the non-linear system by means of a description function is to:
- 395.The pressure switches are two-setting controllers of:
- 396.The biggest difference between the logarithmic characteristics of the spectral characterization of the inertial segment and its substitute characterization - asymptotic - is:
- 397.Which of the standardized analogue electrical signals is the best for the transmission of measurements in the computer measurement path?
- 398.A twisted pair is applied in the transmission of electrical analogue systems because of which of the following?
- 399.The analogue measurement path is connected with the computer by
- 400.Positioner is a device which enables: