F1 Electrical, electronic and control engineering — ETO (CMKE, Poland) — Page 3
586 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 201.A paramagnetic material is:
- 202.Ferromagnetic materials do not include:
- 203.Which point does not describe a magnetically soft material intended for electro-technical application?
- 204.Addition of silicon in electrical steel sheets:
- 205.The Curie temperature is the temperature above which:
- 206.The resistivity of amorphous transformer sheets is of the range of:
- 207.Which of the following answers contains only base units of the SI system:
- 208.Which of the unit conversions is correct?
- 209.In the SI system, an atomic standard is the standard of:
- 210.In a sentence: “the power supply voltage is 5 V,”
- 211.A technical method of resistance measurement is an example of:
- 212.An absolute error in measurement is defined as:
- 213.A relative error in measurement is defined as:
- 214.Voltage was measured using a class 1 voltage meter of the range of 10 V.
- 215.A typical reason for systematic errors is:
- 216.A magnetoelectric converter is composed of the following elements:
- 217.An electromagnetic converter is composed of the following elements:
- 218.An electrodynamic converter is composed of the following elements:
- 219.Extending the DC ammeter range is done using:
- 220.The range of an ammeter of the internal resistance of Ra=1 Ω has been extended 10 times. The resistance of the bypass is:
- 221.The range of a voltage meter of the internal resistance of Rv=100 k Ω has been extended ten times. The resistance of the voltage-range multiplier is:
- 222.An analogue-to-digital converter is designed to:
- 223.The dual-slope integration method is:
- 224.A digital voltage meter is composed of the following sub-assemblies:
- 225.In order to use a magnetoelectric voltage meter to measure the RMS of voltage, it is necessary to:
- 226.The scale of an electromagnetic meter used to measure the AC amperage is scaled in:
- 227.A technical method of resistance measurement requires using the following instruments:
- 228.A digital method of resistance measurement requires using:
- 229.In order to measure resistance, it is necessary to use:
- 230.In a single-phase AC circuit, active power can be measured using:
- 231.The condition of balance for a bridge shown in the figure below is as follows:
- 232.2. The Aron circuit shown in the figure below is used to:
- 233.Analogue frequency meters are manufactured using:
- 234.An indispensable element of a digital frequency meter is:
- 235.The output signal from a thermocouple is:
- 236.A compensating box in a system of temperature monitoring is used to compensate for:
- 237.A three-wire system of connection of a thermoresistor with an unbalanced bridge makes it possible to:
- 238.A piezoresistive pressure transmitter functions on the basis of:
- 239.A potentiometer transducer can be used to measure:
- 240.A tensometric bridge may be power supplied by:
- 241.A digital oscilloscope may not offer a direct measurement of:
- 242.The best analogue signal for transmission at significant distances (>2 m) is:
- 243.An element linking an analogue measurement channel with a computer is:
- 244.The sampling theorem concerns:
- 245.Non-used terminals of “single-ended” voltage inputs of a measurement card should:
- 246.A two-wire twisted pair is used to transmit digital signals because:
- 247.Capacitive semiconductor elements include:
- 248.Junction diode rectifier is built on the basis of:
- 249.Diode terminals are:
- 250.Drop of voltage (threshold voltage) at a silicon diode in the forward direction equals approximately:
- 251.A p-n semiconductor element shown in the figure will enter conduction state when:
- 252.In a system presented in the picture, the waveform of the electrical load current is:
- 253.In small power and average power rectifiers, the following is used most often as a smoothing filter:
- 254.The primary component from which non-controlled rectifiers are made of are:
- 255.In a diode rectifier, the smoothing filter is connected:
- 256.The main parameter of a Zener diode is:
- 257.In order to make use of the stabilising properties of a Zener diode, we connect it:
- 258.The Zener Diode with a breakdown voltage of 5.6 V was connected in a parameter stabiliser assembly to a direct voltage of 9 V. Voltage at the electrical load will not exceed the value of
- 259.A bipolar transistor is built of:
- 260.A bipolar transistor is characterised by the fact that:
- 261.A MOSFET transistor is characterised by the fact that:
- 262.In a JFET transistor, when the gate-source voltage equals zero:
- 263.Electroluminescent LED diodes utilise the following phenomenon:
- 264.Connecting a LED diode to a source of direct current with a value of 12 V requires:
- 265.If there is no external polarisation and there is a lighting of the junction, the photodiode operates as:
- 266.Photoresistor resistance:
- 267.Opto-isolator is an optoelectronics component used most often for:
- 268.Installation of SMT involves:
- 269.An electronic amplifier is an assembly meant to:
- 270.An operational amplifier is:
- 271.In order to excite the oscillator, conditions must be fulfilled regarding the following parameters:
- 272.Trigger circuit is an electronic assembly that:
- 273.Bistable trigger circuits are characterised by:
- 274.In a Schmitt trigger circuit, the threshold levels are determined by changing the relationship between:
- 275.An SCR thyristor is characterised by the fact that:
- 276.A GTO thyristor is characterised by the fact that:
- 277.An IGBT transistor is an assembly that combines the characteristics of:
- 278.Which of the listed non-controller rectifiers generates the greatest average output current:
- 279.An oscillating rectifier in a brushless generator excitation circuit is a rectifier:
- 280.In high power thyristor rectifier assemblies the following is used as an output filter:
- 281.In ship technology, cycloconverter is an electronic power device used primarily as:
- 282.The course of the output voltage generated by the voltage inverter with a voltage control has the following shape:
- 283.A part of a DC machine called the armature corresponds to:
- 284.A part of a DC machine called the magnet corresponds to:
- 285.An external characteristics of the separately excited DC generator is the dependency between:
- 286.The process of self-excitation of a shunt DC generator depends on:
- 287.The relative value of the difference between synchronous speed and rotor speed is called:
- 288.As a result of the start-up with a star-delta switch:
- 289.A doubly-fed motor can be:
- 290.Asynchronous motors are divided into:
- 291.The angular position transducer converting a mechanical signal to an electric one is called:
- 292.Synchros are electrical machines that:
- 293.One of the reasons of sparking in a DC machine can be:
- 294.A slight reduction of excitation current in a shunt DC motor causes:
- 295.What is the relation between power and the output torque of the rotating machine:
- 296.The rated slip in an asynchronous motor totals:
- 297.A series-wound DC motor is characterised by:
- 298.Electrical motors driving anchor winches shall be adapted to:
- 299.The cause of heating up of electrical machines is:
- 300.The rings in an induction motor can be: