F3 Controlling the Operation — Management Level
756 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 1.What does the term "Attained EEDI" mean in MARPOL Annex VI.
- 2.The term INTACT STABILITY means
- 3.Permissible metacentric height GMperm is
- 4.In order to avoid dangerous slamming stresses the bow draught must be
- 5.In the event of a list of 5 degrees to starboard due to negative metacentric height
- 6.Watertight hatches are closed
- 7.Which feature of the tank, loaded with liquid cargo, affects most the free surface correction?
- 8.Permeability of a compartment is
- 9.Which statement about a vessel's stability while dry-docking is TRUE?
- 10.What welding pattern is NOT used to permanently attach a stiffener to a plate?
- 11.A crack in the deck plating of a vessel may be temporarily prevented from increasing in length by
- 12.The type of welding employed in shipyards is primarily
- 13.A vessel has sustained damage in a collision with another vessel. It is necessary to have a Seaworthy Certificate before the vessel sails. Who will issue this certificate?
- 14.The double bottom in a vessel's hull structure is kept from tripping, or folding over, by
- 15.What would have the greatest effect on a vessel's longitudinal strength?
- 16.Which is an advantage of using watertight longitudinal bulkheads in double bottom tanks?
- 17.Which factor does NOT affect the requirements for freeboard of a cargo vessel?
- 18.Progressive flooding may be indicated by
- 19.A continuous worsening of the list or trim indicates
- 20.Which measure should NOT be taken to reduce the slamming of a vessel in head sea waves?
- 21.Which parameter has no effect on the size of the correction of GM for the presence of free surfaces?
- 22.Centre of Buoyancy (B) is the
- 23.Inclining Experiment is done in order to
- 24.The influence of free surface on stability is determined by the ratio between the sum of the free surfaces moments and
- 25.The deformation of the ship's hull called Sagging during Draught Survey means
- 26.What is the result of excessively large transverse metacentric height?
- 27.Does water displacement (Δ) depend on the density of the sea water?
- 28.Which factor has the greatest impact on the size of the correction of GM for free surfaces?
- 29.What affects the size of the "dead load" (the Ship's constant)?
- 30.In determining the quantity of cargo by the ship's draught, the first correction for trim reflects the fact that
- 31.When planning cargo operations, in relation to the stability and strength of the vessel, the Master is guided by
- 32.In cargo operations with shipboard cranes, a ship lists towards the pier without a visible reason. This may be a sign of
- 33.The first correction for trim during draft survey is
- 34.Upon inspection of a bulker, a crack is spotted on the main deck, with a length of 32 cm and starting from the back corner of the coaming of the hatch No 3, starboard side. The most probable reason for this failure is
- 35.Typical damage on the deck of the double bottom of a bulker is
- 36.Enhanced Survey Programme (ESP)
- 37.SOLAS, Chapter XI-1, Reg 2 "Enhanced surveys", refer to
- 38.SOLAS, Part A-1, Reg. 3-2 "Corrosion prevention of seawater ballast tanks" refers to
- 39.Substantial corrosion in ESP Code means that the wear is
- 40.Enhanced inspection on the Res. 1049 (ESP Code) shall be carried out periodically by the
- 41.The planning of the Enhanced inspection on the Res. 1049 (ESP Code) shall be carried out periodically by the
- 42.A ship undergoes four types of surveys during its 5 yearly cycle of statutory surveys: 1. Annual Survey; 2. Intermediate survey; 3. Renewal Survey; 4. Dry dock survey. So where does Enhanced survey programme fit in these?
- 43.Why is the remaining area in the Intact stability diagram, upon checking the stowage plan for grain in bulk, called residual dynamic stability?
- 44.Why are most break bulk vessels built with a transverse framing system rather than a longitudinal system?
- 45.If a vessel is sagging, what kind of stress is affecting the sheer strake?
- 46.When a vessel is stationary and in a hogging condition, the main deck is under
- 47.If the event of a large list caused by negative initial stability, counter flooding into empty tanks may
- 48.IMSBC Code establishes the following Special provisions for the transport of cohesive bulk cargo with multi-deck ship.
- 49.Are there any additional requirements for the stability of PCC‘s (Pure car carries)?
- 50.Cargoes of IMO Class 3 are divided into subclasses
- 51.The cargoes from Group B in IMSBC Code are
- 52.Supervision of the technical condition of the containers in operation is performed according to
- 53.What is the purpose of the trimming of cargo, according to the IMSВС Code?
- 54.INF Ships
- 55.Тhe net tonnage of the vessel – „NT” includes
- 56.The term "angle of flooding" in the Code for the carriage of grain in bulk (Int. Grain Code) means
- 57.Which ships should have "Stability information"?
- 58.For the transport of timber on deck, the ship’s stability at the end of the voyage
- 59.In respect of the carriage of timber deck of the ship, non-technical metacentric height must be at least
- 60.All ship loading devices must be checked and the results recorded in the cargo gear record book at intervals of
- 61.What is the meaning of "SWL"?
- 62.Enhanced Survey requirement of Res. 1049 (ESP Code), is carried out periodically by the
- 63.SOLAS, Chapter XI-1, Reg. 2 "Enhanced surveys", refer to
- 64.Substantial corrosion means that the wear is
- 65.Bulk carriers with short and long holds are built so for
- 66.For the carriage of grain in bulk the residual area on the Intact Stability diagram must be a minimum of
- 67.For the carriage of grain by ship without the "Document of authorization" saucer is used to
- 68.For the carriage of grain by ship without “Document of authorization”, the heeling moment of partially filled compartment is
- 69.According to the Grain Code, cross curves of stability at 120 shall be included in the Stability information. This is required for the
- 70.Should a partially filled compartment, with grain in bulk, be trimmed?
- 71.Assumed angles on the shifting of grain in the requirements of the Grain Code for new ships are
- 72.Fixing the surface of grain in bulk with Saucer or Bundling
- 73.Requirements for static heel ≤ 12° and remaining area on the Intact Stability diagram, S ≥ 0.075 m. rad, are demonstrated
- 74.Is the certification of a cargo plan for carriage of goods, listed in the IMSBC Code, mandatory in Bulgarian ports?
- 75.What is an “AFRAMAX” type of ship?
- 76.When checking the stowage plan for general cargo, dynamic stability is determined by
- 77.In the distribution for the specified stability, resonance period of transverse rolling is set
- 78.Trim by the stern
- 79.According to the CSS Code, the securing of steel coils by means of wedges is
- 80.According to the CSS Code, Calculation strength (CS) is
- 81.According to the CSS Code, the SAFETY FACTOR (SF) is
- 82.Seawaymax
- 83.BLU Code is a code of IMO and refers to
- 84.Areometer is an instrument designed to measure the
- 85.In accordance with the recommendation in the TDC Code metacentric height
- 86.Six digit code system to indicate the container cells in container ships, for example 01 03 02, means the number of
- 87.What does the term "MHB" mean?
- 88.The term VCF means the
- 89."Safety Construction certificate of cargo ship" is issued for a period not exceeding
- 90."Administration" according to MARPOL and SOLAS is
- 91.If there are several original Bill of lading issued, the carrier:
- 92.What should be the lifeboat capacity on a cargo ship with a length greater than 85 meters?
- 93.What should be the lifeboat capacity on a passenger ship?
- 94.What shall be the capacity of the life-rafts on a cargo ship with a length greater than 85 meters?
- 95.The abbreviation “EEDI” means:
- 96.If the external condition of the cargo or its packaging give sufficient grounds for doubt for damages
- 97.If the sender does not deliver, within the agreed period, the cargo for carriage
- 98.If the vessel violates the requirements of the MARPOL Convention, on the territory of another party of the Convention, the penalties shall be determined by the
- 99.If a cargo, handed over to the storage, is not contacted by the recipient and are not paid the amounts due on the transport
- 100.What is the new record book introduced by the MARPOL Annex VI?