F4 Marine Engineering — Operational Level — Page 3
283 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 201.What is the relationship between the terms “Maximum continuous power” and “Rated power” of the main ship engine:
- 202.What is the structural strength of a material?
- 203.What is the thermal load distribution of the cylinder liner of a ship engine
- 204.What is the typical slow down temperature at oil outlet of a low speed ship engine
- 205.What is usually the value of the "Slow down/Shut down" temperature at the cooling water outlet of the low speed Marine internal combustion engine?
- 206.What kind of induction is the presence of high quantity of tin in the marine internal combustion engine oil when oil analysis is carried out?
- 207.What kind of material are the large engine parts made from?
- 208.What losses does the indicated efficiency register in addition to those of the thermal efficiency?
- 209.What material is the cylinder liner of the marine diesel engine made of?
- 210.What needs to be measured in order to determine in ship conditions of the indicator efficiency:
- 211.What quality must the fresh water have for normal boiler operation
- 212.What should be measured to determine the effective efficiency of a ICE in a ship:
- 213.What type are the mean bearings in the ship engine?
- 214.What type of pumps are most suitable for use as feed pumps for bilge separators
- 215.What would the excessive temperature rise at the end of the process of compression in carburetor internal combustion engine lead to?
- 216.When a Marine internal combustion engine operates on low sulphur-content fuel, the cylinder oils must be with:
- 217.When does the governor characteristic of the Main internal combustion engine have to be static:
- 218.When does the system for heating, purging and venting the steam work?
- 219.When is compressed air admitted into the cylinder at start-up?
- 220.When is it needed the governor characteristics of the ICE to be static:
- 221.When operating ships engines with low sulfur-content fuels what cylinder oils should be used?
- 222.When the condenser tubes are flared in both tube plates, the different degree of linear expansion is compensated using:
- 223.When the main internal combustion engine, controlled by a load-limiting governor, cannot reach the set speed, it works on:
- 224.When the main engine is fully loaded, the T/C speed is too low. What could be the reason?
- 225.When the main ship engine works with low-sulphur content fuels are used cylinder oils with:
- 226.When the pH of the boiler water decreases to "0", the water becomes:
- 227.Where are the additional heating surfaces in the steam boiler installed?
- 228.Where are the additional heating surfaces of the boiler installed?
- 229.Where is the air-fuel mixture formed in the marine diesel engines?
- 230.Which supercharging system has the higher efficiency of the turbine unit?
- 231.Which boilers with equal characteristics have the highest steam generating capacity?
- 232.Which element of the starting system is used for the restart of the ship engine made with open compressed air bottles?
- 233.Which forced induction air system has higher efficiency of the turbine side?
- 234.Which forced-induction system has a higher turbine efficiency?
- 235.Which governor characteristic of the marine diesel engine is called astatic:
- 236.Which governor characteristic of the ship internal combustion engine has statism:
- 237.Which indicated parameter can we directly measured on the engine?
- 238.Which indicator characterizes the load of the heat recovery boilers?
- 239.Which indicator characterizes the load of the waste steam boilers
- 240.Which indicator parameters should be measured in order to obtain the indicator efficiency
- 241.Which of the casting methods produces from any material blanks with high density and precision, low surface roughness and complex configuration?
- 242.Which of the following bearings are most widely used as main bearing and connecting rod bearings in the Main internal combustion engines?
- 243.Which of the following causes a buildup and clogging of the nozzle openings of the diesel engine fuel valves?
- 244.Which of the following describes the mechanism of the chemical process that takes place in the water when the boiler is in operation?
- 245.Which of the following forced induction systems has the lowest efficiency of the turbine part?
- 246.Which of the following forced induction systems has the lowest efficiency of the turbine unit?
- 247.Which of the following is materials is the most widely used in shipbuilding?
- 248.Which of the following is the most likely reason for overheating of the main bearings?
- 249.Which of the following power systems has the greatest service life?
- 250.Which of the following principles does not apply to the heat transfer in a ship steam boiler?
- 251.Which of the following statements describes the mechanism of a chemical process, that occurs in the water during the operation of a marine boiler?
- 252.Which of the following statements is true about water and fire tube boilers?
- 253.Which of the listed indirect indicators reflects the most precisely the power developed by the main ship engine?
- 254.Which of the specified chemical elements are harmful for the steel?
- 255.Which of the statements is Carnot's theorem?
- 256.Which parts of the ship engines form the workspace?
- 257.Which processes in the boiler does the reaction of the boiler water affect?
- 258.Which ship engines have scavenging ports
- 259.Which statement is true for centrifuges pumps?
- 260.Which test determines the dry residue in boiler water?
- 261.Why is additional lubrication necessary in the cylinder liner of the Marine internal combustion engines?
- 262.Why is additional lubrication of the cylinder liner of ICE necessary?
- 263.Why is additional lubrication of the cylinder liner of the main ship engine needed?
- 264.Why is it important to maintain the pH of the boiler condensate within acceptable limits?
- 265.Why is it recommended to top up with vaporized freon?
- 266.Why is the coefficient of excess air in modern main engines kept high at rated power:
- 267.Why should the adjustment of cylinder oil supply with cross-headed engines be checked?
- 268.Why should the Marine internal combustion engine cylinder liners be able to expand freely in radial and axial directions?
- 269.With crosshead ship engines the oil temperature in the low pressure oil system is
- 270.With the marine diesel engine the process of compression is a thermodynamic process in which of extreme importance is:
- 271.With the marine ICE the connection of the starter system to the compressed air bottles is accomplished by:
- 272.With a constant cycle portion, when increasing the revolutions, which phase of combustion changes the most, measured by the angle of rotation of the crankshaft?
- 273.With a PGA type governor, when using viscosity oil other than that recommended by the manufacturer, it is necessary:
- 274.With earlier fuel injection, the mean indicator pressure of the modern Marine main engine increases as much as the:
- 275.With gas turbine units the good fuel-air mixture is ensured by:
- 276.With modern main engines, in case of early fuel injection, the mean indicator pressure increases by as much as
- 277.With modern main engines how does the effective efficiency change when the combustion starts earlier?
- 278.With ship engines what is the main form of development of combustion in its second phase
- 279.With ship engines, what is the main form of development of combustion in its fourth phase?
- 280.With the 2-stroke Marine internal combustion engines, what does "useful volume" mean?
- 281.With the same ignition delay period, the high evaporation of the fuel:
- 282.With the same mass and dimensions, which steam turbines have the higher power?
- 283.With which main engine is required additional injection of oil into the cylinder liner?