F4 Marine Engineering — Operational Level
283 questions with correct answers. Click a question to see its answer.
Take the full test →Random exam test generator, free, no registration- 1.The ratio of the total volume of the cylinder to the volume of the combustion chamber is called:
- 2.In a modern ship main engine the mean indicated pressure in case of early fuel injection
- 3.Is it possible the mechanical loss coefficient (the mechanical еefficiency) to be used for passing from indicated to effective “P” parameters at all “n”
- 4.The additional heating surface in which the saturated steam is dried and overheated is called
- 5.The crank shaft deflection in internal combustion engines carries information about:
- 6.Why should the timing of cylinder oil feeding in crosshead marine diesel engines be checked?
- 7.According to the second law of thermodynamics, transformation of thermal energy in mechanical work is possible when
- 8.According to the steam flow direction, the steam turbines are divided into:
- 9.According to their type, fuel injection pumps in gas turbine units are
- 10.According to their working principle, the oil systems on the gas turbine units are:
- 11.According to what law do direct action engine governors operate?
- 12.Air cooling after turbocharger units results in:
- 13.An alloy consisting of copper and tin is called:
- 14.An indirect indicator of the "load" of the marine internal combustion engine could be:
- 15.Are four-stroke internal combustion engines started by compressed air?
- 16.As the air temperature at the inlet of the cylinder increases, which of the combustion phases is reduced?
- 17.At rotation speeds from 70 to 100% of the nominal one and the same propeller characteristic, the wear of the piston-cylinder group of the ship's engine
- 18.At what minimum temperature of the engine room can the start of the main ship engine be started?
- 19.Best regulation of the steam turbine is achieved when:
- 20.Boiler water hardness is due to:
- 21.Boilers that use the heat of the main engine exhaust gases are called?
- 22.By which method external cone surfaces are machined by chip removal?
- 23.Chlorine is added to the coolant fresh water of the ICE to:
- 24.Could the T/C surging be caused by factors outside the turbocharger?
- 25.Do four- stroke ship engine start with compressed air
- 26.Does the gas turbine have an axial-radial bearing / thrust bearing / like the main IC Engine?
- 27.Does the magnitude of the force with which the nuts of the bolts that connect the foundation frame to the ship's foundation have any importance?
- 28.During which piston stroke does the process of compression of the working medium in the marine diesel engine take place?
- 29.Earlier or later than the optimum fuel injection in ICE:
- 30.Exhaust gas temperatures of a four-stroke marine diesel engines
- 31.Exhaust gas temperatures with four stroke main engine
- 32.For which fixed part of the marine diesel engine are the cross-head guides attached?
- 33.How does the effective efficiency of modern main ship engines change when combustion starts earlier
- 34.How can it be determined that a refrigerator compressor works in a "wet stroke"?
- 35.How does the creation of vortex air movement affect the quality of the compression process in a ship engine?
- 36.How does the increasing of the excess air coefficient affect the corrosion of the gas side of the Marine steam boiler
- 37.How does the thermal stress of ship engines change with the increase of the excess air ratio?
- 38.How is the cylinder liner fixed to the cylinder block of the main ship engine?
- 39.How is the Marine Steam Boiler secured to the hull?
- 40.How is the cylinder liner mounted to the cylinder block of the Main internal combustion engines?
- 41.How low should be the flash point of the crankcase lub. oil of the auxiliary diesel engine?
- 42.How many loop does the main turbine unit oil system have ?
- 43.How many pressure gauges should be mounted on each Marine Steam Boiler?
- 44.How many water level glasses are mounted on each boiler with a working pressure above 5 Bar?
- 45.How much is the power of the marine internal combustion engine if the rotation speed(RPM ) and the mean effective pressure are 90% from the nominal?
- 46.How to prevent the leakage of water from the cooling space between the liner and the body of the cylinder block in ship engines
- 47.How will the reduction of the crank-angle of injection affect the operation of the T/C?
- 48.If the internal combustion engine's revolutions and the beginning of the fuel injection are constant, with the increase of the cetane number of the fuel, the rate of increase of the pressure in the cylinder during the second combustion phase:
- 49.If the 4 stroke engine is started with air, admitted directly in the cylinders, the piston in the cylinder must be in the following position:
- 50.If the indicator actuator is properly adjusted, if the fuel supply to the ship’s engine cylinder is stopped, the mean indicator pressure is
- 51.If the propeller curve is with 80% slope from the nominal and nominal speed is set, what will be the engine power
- 52.If the propeller operates at "heavy" characteristic and if we set nominal revolutions, the engine
- 53.If the water in the oil forms an emulsion, can separation remove the water?
- 54.If the water level cannot be seen at the bottom part of the level indicator glass of the boiler, which of the following actions should be taken immediately
- 55.If with a continuous fuel feed we reduce the speed of the main ship engine, what changes in its parameters will we see?
- 56.In a modern ship main engine the mean indicated pressure in case of early fuel injection increases as much as :
- 57.In accordance with its principle of operation, the oil systems on the gas turbine are divided into:
- 58.In case of wear of the openings of the nozzle tip of the ship engine, the indicator efficiency
- 59.In modern ship engines, the advance of the fuel injection is optimized to affect
- 60.In order to determine the indicated power of the ICE, it is necessary to measure:
- 61.In ship steam boilers, what does the steam multiplicity factor indicate?
- 62.In the high-pressure oil system, the number of oil pumps is most often:
- 63.In the steel- carbon diagram, which is the factor that differentiates steel and cast iron?
- 64.In which cases the hydrodynamic efficiency of the propeller is zero?
- 65.In which part of the cylinder liner of the main ship engine piston wear the greatest?
- 66.Is the amount of air theoretically necessary to burn a unit of diesel the same as the amount of air necessary to burn a unit of gasoline?
- 67.Is the main starting valve a mandatory element in the starting air system?
- 68.Is the steam turbine a reversible machine?
- 69.Is there a difference between static and the astatic governor characteristic of the main ship engine?
- 70.Is there a difference in the design of the fuel nozzles of the Main IC Engine and main turbine unit?
- 71.Lowering the maximum pressure of fuel injection when operating the main ship engine during maneuvers is due to:
- 72.Marine internal combustion engine with wet sump system indicates:
- 73.Marine boilers that have their own combustion chamber are called:
- 74.Marine steam boilers that have their own combustion chamber are called:
- 75.Nozzle boxes are an element of a gas turbine that are fixed to
- 76.One of the functions of the air collector of a ship's engine is
- 77.Propeller curve is the characteristic of the :
- 78.Reversal of the main ship engine is required when:
- 79.Seals used in steam turbines are
- 80.ship internal combustion engine's oil filters are:
- 81.Some of the internal combustion engines have rotating valves. What is the reason for this?
- 82.Specify the correct chemical equation of the reaction called "carbon oxidation'
- 83.Steam turbine guide vanes are fixed vanes and are attached to
- 84.Steam turbines driving the propeller are called:
- 85.Steam turbines produce mechanical energy using
- 86.Sudden pressure drop in the steam boiler can lead to
- 87.Surging in the marine internal combustion engine turbo charger is caused by:
- 88.The properties of diesel fuels are determined by:
- 89.The adjustment of the indicator drive influences the measuring of the
- 90.The boiler's accumulating capacity is determined by:
- 91.The check for correct adjustment of the indicator drive of the operating marine ICE is done by taking
- 92.The circulating oils for the Marine internal combustion crosshead engines (crankcase oils) in comparison with the circulating oils for the trunk engines have:
- 93.The clearance meter is:
- 94.The cooling water of the main ship engine is used in the fresh water generator as:
- 95.The corrosion properties of diesel fuels are characterized by:
- 96.The devices for accelerating the steam in steam turbines are called:
- 97.The devices that preheat the air entering the combustion chamber of the Gas Turbine Engine are called:
- 98.The difference in the structures of cast iron and steel is due to:
- 99.The distances between endpoints in length, breadth and height of the ship internal combustion engines are called:
- 100.The fuel oil consumption, consumed for unit time per unit power is called: