F1 Mechanika okrętowa — oficer mechanik wachtowy — Strona 5
489 pytań z poprawnymi odpowiedziami z bazy CMKE. Kliknij pytanie, aby zobaczyć odpowiedź.
Rozwiąż cały test →Generator testów egzaminacyjnych z losowymi pytaniami, bez rejestracji- 401.It is a thin plate with a hole that is usually used to distribute the load of a threaded fastener, such as a screw or nut.
- 402.The appliance that is used for the removal of oil from the bilges before pumping overboard.
- 403.A measure of a fluid’s resistance to flow.
- 404.The main source of fuel injection system malfunctions.
- 405.To evacuate crew and passengers from a vessel following a distress.
- 406.What does the bore of a diesel engine describe?
- 407.“Check the bilge pumps of the lifeboats and report.”
- 408.Often harmful gas produced by fires, chemicals, fuel, etc.
- 409.“The air compressor will be …. in the repair yard.” Which word is the odd one?
- 410.One end of a diesel engine cylinder is sealed by the cylinder head and the other end by:
- 411.It is a mechanical seal which fills the space between two or more mating surfaces. It generally prevents leakage from or into the joined objects while under compression.
- 412.The instrument that is probably the most commonly used for determining valve clearances.
- 413.“Do not enter the unmanned engine room without ….. .”
- 414.The power tool that is used for finishing of metallic surfaces.
- 415.Current that flows in only one direction.
- 416.To set correctly in relation to other components.
- 417.Which of the terms mentioned below is not used for oil separation?
- 418.The element that connects the piston to the crosshead in two-stroke crosshead engines.
- 419.The method that is not a fire extinguishing method.
- 420.The unit of electrical resistance.
- 421.“When a gas is compressed, its temperature will increase.” Which word can be used instead of the word written in bold?
- 422.The element that the piston rings have a direct contact with.
- 423.The most common source of excitation for synchronous motors.
- 424.If a fire breaks out in the fuel tanks of the vessel, the fire will be ...
- 425.A fuel / air mixture below the lower explosive limit is:
- 426.“We require a ……… generator to operate an …….. pump.”
- 427.The place that is assigned to crew and passengers where they have to meet according to the muster list when corresponding alarm is released or announcement made.
- 428.Escape of liquids such as water, oil, etc. out of pipes, boilers, tanks.
- 429.The rate of electric current flow through a conductor is measured in:
- 430.The element that is not a running part of a diesel engine.
- 431.“Check the securings of the launching appliances and report.”
- 432.The piping arrangement that allows one stream of liquid or gas to be directed into two or more pipes.
- 433.“Post a fire watch in a fire area.” The order means:
- 434.Electric circuits are protected against short circuits and overloads by means of:
- 435.The burning of fuel and air mixture in the cylinder.
- 436.The centrifugal separator that is used for the removal of solids and water from lube oil and fuel oil.
- 437.The element that is not a stationary part of a diesel engine.
- 438.The unit that makes use of gravity.
- 439.“Pressure in the water pipe is too low.”
- 440.Electrical power is expressed in:
- 441.The term that indicates the sequence of events that take place in the cylinder of an engine.
- 442.Accidental escape of oil out of a tank when it gets too full because pumping was not stopped in time.
- 443.A group of crew members trained for fighting flooding in the vessel.
- 444.The event that does not take place the moment the piston has just reached TDC.
- 445.The appliance that converts mechanical energy into electrical energy.
- 446.The general emergency alarm sounded by the detection system.
- 447.Ambient temperature is:
- 448.Vertical partitions that provide strength and compartmentation.
- 449.The tool that is used for cutting keyways, narrow grooves, square corners.
- 450.When you detect a fire, first of all:
- 451.The material that can resist bending is:
- 452.The tailshaft is usually supported by:
- 453.The term that is used to describe the work that may cause heat, sparks, flames and which must never be carried out until a special permit is obtained,
- 454.The tools that are used for cutting external threads.
- 455.The pump that displaces liquid on both the forward stroke and the return stroke.
- 456.The part that is directly exposed to the combustion.
- 457.The area of the vessel that presents a greater risk of fire.
- 458.The excessive pressure in a piping system is discharged by:
- 459.Air or fuel problems in a diesel engine are indicated by:
- 460.Friction, engine wear, and oil consumption in a diesel engine are directly related to:
- 461.In a diesel engine, the main bearings are used between:
- 462.Fuel oil commences injection into the cylinder of a four-stroke cycle diesel engine during:
- 463.In a diesel engine, maximum lube oil system pressure is normally controlled by:
- 464.“Gas will expand when heat is applied.” Which of the below mentioned statements has the same meaning?
- 465.The piston is connected to the connecting rod by:
- 466.Lubricating systems for diesel engines are usually designed to initially provide lubricating oil to:
- 467.Valves in the cylinder head of a diesel engine are opened by:
- 468.List of crew, passengers and all on board and their functions in a distress or drill.
- 469.C/E or an engineer handing over the watch should say:
- 470.Connecting rods in a diesel engine are used to connect:
- 471.The best tool that is used to measure the number of threads at a given distance on a bolt.
- 472.In a supercharged two-stroke diesel engine, the exhaust gases are expelled from the cylinder by:
- 473.The wrench that is least likely to slip off a bolt head or nut.
- 474.A wattmeter is used to determine:
- 475.CO2 fire extinguishing systems put out fires by:
- 476.“Is the vessel seaworthy?”
- 477.“The fire dampers in no. 2 hold are painted stuck.”
- 478.In a large slow-speed main propulsion diesel engine, sea water is used to directly cool:
- 479.The action that shouldn’t be taken when cooling down a fire.
- 480.The component that reseats intake valve in a diesel engine.
- 481.In accordance with MARPOL regulations and safe tanker practices, if a cargo hose shows a small leak in its fabric, it is not allowable to resume the oil transfer until:
- 482.Which of the mentioned below is hot work?
- 483.Chemicals are added to boiler feedwater to:
- 484.A pipe coupling is a type of fitting that is usually characterised by:
- 485.The type of energy that is associated with the water of an operating boiler.
- 486.Lube oil is preheated before centrifugation in order to:
- 487.The instrument that is most commonly used to measure exhaust gas temperature of cylinders.
- 488.Most solenoid valves are actuated by:
- 489.Both evaporators and condensers are two types of: