F1 Elektrotechnika, elektronika i automatyka — elektroautomatyk — Strona 4
750 pytań z poprawnymi odpowiedziami z bazy CMKE. Kliknij pytanie, aby zobaczyć odpowiedź.
Rozwiąż cały test →Generator testów egzaminacyjnych z losowymi pytaniami, bez rejestracji- 301.The most common source of excitation for synchronous motors.
- 302.If a fire breaks out in the fuel tanks of the vessel, the fire will be ...
- 303.A fuel / air mixture below the lower explosive limit is:
- 304.“We require a ……… generator to operate an …….. pump.”
- 305.The place that is assigned to crew and passengers where they have to meet according to the muster list when corresponding alarm is released or announcement made.
- 306.Escape of liquids such as water, oil, etc. out of pipes, boilers, tanks.
- 307.The rate of electric current flow through a conductor is measured in:
- 308.The element that is not a running part of a diesel engine.
- 309.“Check the securings of the launching appliances and report.”
- 310.The piping arrangement that allows one stream of liquid or gas to be directed into two or more pipes.
- 311.“Post a fire watch in a fire area.” The order means:
- 312.Electric circuits are protected against short circuits and overloads by means of:
- 313.The burning of fuel and air mixture in the cylinder.
- 314.The centrifugal separator that is used for the removal of solids and water from lube oil and fuel oil.
- 315.The element that is not a stationary part of a diesel engine.
- 316.The unit that makes use of gravity.
- 317.“Pressure in the water pipe is too low.”
- 318.Electrical power is expressed in:
- 319.The term that indicates the sequence of events that take place in the cylinder of an engine.
- 320.Accidental escape of oil out of a tank when it gets too full because pumping was not stopped in time.
- 321.A group of crew members trained for fighting flooding in the vessel.
- 322.The event that does not take place the moment the piston has just reached TDC.
- 323.The appliance that converts mechanical energy into electrical energy.
- 324.The general emergency alarm sounded by the detection system.
- 325.Ambient temperature is:
- 326.Vertical partitions that provide strength and compartmentation.
- 327.The tool that is used for cutting keyways, narrow grooves, square corners.
- 328.When you detect a fire, first of all:
- 329.The material that can resist bending is:
- 330.The tailshaft is usually supported by:
- 331.The term that is used to describe the work that may cause heat, sparks, flames and which must never be carried out until a special permit is obtained
- 332.The tools that are used for cutting external threads.
- 333.The pump that displaces liquid on both the forward stroke and the return stroke.
- 334.The part that is directly exposed to the combustion.
- 335.The area of the vessel that presents a greater risk of fire.
- 336.The excessive pressure in a piping system is discharged by:
- 337.Air or fuel problems in a diesel engine are indicated by:
- 338.Friction, engine wear, and oil consumption in a diesel engine are directly related to:
- 339.In a diesel engine, the main bearings are used between:
- 340.Fuel oil commences injection into the cylinder of a four-stroke cycle diesel engine during:
- 341.In a diesel engine, maximum lube oil system pressure is normally controlled by:
- 342.“Gas will expand when heat is applied.” Which of the below mentioned statements has the same meaning?
- 343.The piston is connected to the connecting rod by:
- 344.Lubricating systems for diesel engines are usually designed to initially provide lubricating oil to:
- 345.Valves in the cylinder head of a diesel engine are opened by:
- 346.List of crew, passengers and all on board and their functions in a distress or drill.
- 347.“Assemble on the quarter deck … … !”
- 348.Connecting rods in a diesel engine are used to connect:
- 349.The best tool that is used to measure the number of threads at a given distance on a bolt.
- 350.In a supercharged two-stroke diesel engine, the exhaust gases are expelled from the cylinder by:
- 351.The wrench that is least likely to slip off a bolt head or nut.
- 352.A wattmeter is used to determine:
- 353.CO2 fire extinguishing systems put out fires by:
- 354.“Is the vessel seaworthy?”
- 355.“The fire dampers in no. 2 hold are painted stuck.”
- 356.In a large slow-speed main propulsion diesel engine, sea water is used to directly cool:
- 357.The action that shouldn’t be taken when cooling down a fire.
- 358.The component that reseats intake valve in a diesel engine.
- 359.In accordance with MARPOL regulations and safe tanker practices, if a cargo hose shows a small leak in its fabric, it is not allowable to resume the oil transfer until:
- 360.Which of the mentioned below is hot work?
- 361.Chemicals are added to boiler feedwater to:
- 362.A pipe coupling is a type of fitting that is usually characterised by:
- 363.The type of energy that is associated with the water of an operating boiler.
- 364.Lube oil is preheated before centrifugation in order to:
- 365.The instrument that is most commonly used to measure exhaust gas temperature of cylinders.
- 366.Most solenoid valves are actuated by:
- 367.Both evaporators and condensers are two types of:
- 368.Do elementów półprzewodnikowych objętościowych zaliczamy:
- 369.Złączowa dioda prostownicza zbudowana jest na bazie:
- 370.Złącza diody to:
- 371.Spadek napięcia (napięcie progowe) na diodzie krzemowej w kierunku przewodzenia wynosi w przybliżeniu:
- 372.Element półprzewodnikowy p-n pokazany na rysunku wejdzie w stan przewodzenia, gdy zostanie:
- 373.W układzie pokazanym na rysunku przebieg prądu odbiornika jest:
- 374.W prostownikach małej i średniej mocy jako filtra wygładzającego używa się najczęściej:
- 375.Zasadniczą częścią z jakich zbudowane są prostowniki niesterowane są:
- 376.W prostowniku diodowym filtr wygładzający włączamy:
- 377.Głównym parametrem diody Zenera jest:
- 378.Aby wykorzystać własności stabilizujące diody Zenera włączamy ją:
- 379.Diodę Zenera o napięciu przebicia 5,6 V podłączono w układzie stabilizatora parametrycznego do napięcia stałego o wartości 9 V. Napięcie na odbiorniku nie przekroczy wartości
- 380.Tranzystor bipolarny zbudowany jest z:
- 381.Tranzystor bipolarny charakteryzuje się tym, że:
- 382.Tranzystor MOSFET charakteryzuje się tym że:
- 383.W tranzystorze JFET, gdy napięcie bramka-źródło równa się zero:
- 384.W diodach elektroluminescencyjnych LED wykorzystane jest zjawisko:
- 385.Podłączenie diody LED do źródła napięcia stałego o wartości 12 V wymaga:
- 386.Przy braku polaryzacji zewnętrznej i oświetleniu złącza fotodioda pracuje jako:
- 387.Rezystancja fotorezystora:
- 388.Transoptor to element optoelektroniczny najczęściej wykorzystywany do:
- 389.Montaż SMT polega na:
- 390.Wzmacniacz elektroniczny to układ, który ma za zadanie:
- 391.Wzmacniacz operacyjny to:
- 392.Aby generator drgań został wzbudzony, muszą być spełnione warunki:
- 393.Przerzutnik to układ elektroniczny, który:
- 394.Przerzutniki bistabilne charakteryzuje:
- 395.W przerzutniku Schmitta poziomy progowe ustala się przez zmianę stosunku:
- 396.Tyrystor SCR charakteryzuje się tym, że:
- 397.Tyrystor GTO charakteryzuje się tym, że:
- 398.Tranzystor IGBT to układ łączący w sobie cechy:
- 399.Który z wymienionych prostowników niesterowanych generuje największy średni prąd wyjściowy:
- 400.Prostownik wirujący w obwodzie wzbudzenia prądnicy bezszczotkowej to prostownik